Turbo Plenum Straps

Made up some straps from strips of aluminium, used the engine mounts and plenum fixings to hold in place.

Turbo Mapping at RLM Racing

Took my car to RLM Racing to be mapped, all in all the car was on the dyno for a couple of days and I am really happy with the results. 

I asked Rich to map the car so that it would be drivable and to have a progressive power curve. Looking at the dyno plots he achieved this quite nicely. 

The MBE 9A9 ecu was set up to have switchable maps for different levels of boost. Low boost at 0.6 Bar, medium at 1 Bar and high at 1.3 Bar. This equates to around 250 / 310 / 400 wheel Hp. I have the option to cap the boost in the lower gears and then to fit front wheel sensor for traction control. I will try capping the boost in 1st and 2nd gears for the time being.

The GT28/76 turbo was the limiting factor and would not achieve more than 1.4 Bar and then tailing off to 1.3 Bar. With a larger turbo the engine is capable of making more power but may cause turbo  lag. For now 400 wheel hp will be plenty. 

On higher boost the plenum blew off so I will need to makeup some straps to keep it I place, Rich wired it down temporarily.

The charge cooler performed well and managed to keep inlet temperatures at a reasonable level, looking forward to see how it performs on the road and track.

Next step is to upgrade the brakes and wait for the weather to get better.

Turbo Final Assembly

Fitted the plenum and connected to the throttle bodies with 50mm long silicone joining sections. Had connections fitted to the ends of the plenum to allow straps to be fitted to hold down the plenum under boost. 

I fitted the boost Pipework and used 3 inch aluminium tubing between the elbows. The charge cooler is 3 inch in and out and then the plenum is also 3 inch. Covered the charge cooler in reflective heat shield to try to keep the coil cool and to reduce heat soak from the engine bay. 

Fitted a second water pump and radiator for the cooling water system on the charge cooler. The  pump runs when the engine is running and circulates water between the rad and the charge cooler core.

The car is now off to RLM for mapping, so fingers crossed for a good result.

Hayabusa Turbo Plenum

The plenum has been made for me by G19 Engineering, Doug made the plenum for me based on my  design. I am really happy with the results.

The base is made from billet and had been cnc machined for precision. The inlets have been machined beveled for maximum air flow. 

The take offs at the bottom are for boost pipes to the map sensor and the fuel pressure regulator. The temp sensor fits in the centre.

Turbo Raceco Exhaust

Fitted a 3 inch Raceco titanium exhaust silencer. Used a Caterham exhaust bracket that I bought online and fixed to the body tub with a large repair washer on the inside. This fits perfectly with the angled Caterham style bracket on the end can.

The silencer is incredibly light and the quality is superb, the silencers finish really goes well with the brushed stainless down pipe. 

Lock Up Multi Stage Clutch

Managed to get a good deal on a MTC multi stage lock up clutch kit from a drag racer. The kit was fitted to a 620hp turbo hayabusa and used for full bore launches at 10,000 rpm. So should be more than capable to stop my clutch slipping with the higher power engine.

The clutch kit comes with a MTC billet inner hub that completely replaces the stock clutch centre and back torque limiter, a billet clutch basket, a modified clutch pressure plate, updated springs, and an updated clutch centre that has spring loaded arms that sequentially push the pressure plate down above 5,000 rpm and locking the clutch in place. There is also a larger billet clutch cover with a removable access lid for easy clutch adjustments. 

I decided to keep the Extreme Engines billet basket and to put the MTC item on eBay, which I'll list at a later date. In a drag application where the clutch is designed to slip before it locks, the racers often run more steel plates than fibre. For the time being I am going to run the standard clutch set up with the half plate at the back swapped for a full plate.

Turbo Rebuild #11 - Downpipe Welded

Some pictures if the down pipe that's been TIG welded by G19 Engineering. Hopefully the plenum will follow shortly.